What AH36 Plate Is
AH36 is a high strength hull structural steel with a minimum yield strength of 355 MPa, defined under the classification society rules that govern shipbuilding. The letter A denotes impact testing at 0 degrees C, the H marks higher strength hull steel, and 36 gives the minimum yield in kgf/mm2. It sits above the ordinary A-grade hull steel and below the higher grades such as AH40, and it is one of the most widely used plates in commercial shipbuilding.
The grade is controlled by chemistry and by heat treatment. Normalized plate gives a uniform ferrite-pearlite structure and predictable toughness, while thermo-mechanically controlled rolling delivers the same strength with lower carbon and better weldability. Which route applies depends on the plate thickness and on the society rules being followed, so the order should state the grade, the thickness range and the delivery condition together.
Classification Society Approval
Hull steel is bought against a class society certificate, not only against a mill certificate. The common societies are ABS, BV, CCS, DNV, LR, NK and KR, and each publishes its own rules for chemistry, mechanical properties and testing frequency. Plate supplied for a classed vessel has to be produced by an approved mill and surveyed by the society, with the certificate traceable to the heat number on the plate.
For a project, tell us which society and which grade notation applies, and whether the plate is for hull, deck, bulkhead or a secondary structure. Approval is granted per mill and per thickness range, so a change of mill or of delivery condition can require re-approval. Where a buyer needs several societies, that has to be agreed before rolling rather than after inspection.
Thickness Range and Plate Formats
AH36 is commonly supplied from 6 mm to 100 mm, with widths up to about 3200 mm and lengths to 12 m or more depending on the mill. Plates up to 6 m are easier to handle and cut; longer plates reduce the number of seams in a hull but need suitable lifting gear and transport. Thickness tolerance, flatness and edge condition all matter on a hull where plates are butted and welded in sequence.
Plate is normally supplied in the as-rolled or normalized condition with mill edge or sheared edge. Specify whether you need ultrasonic testing for internal soundness, and at what acceptance level, because that changes both the price basis and the lead time. Cutting to size at the mill can reduce site waste, but it fixes the nesting before the yard has finalised its cutting plan.
Welding and Fabrication
AH36 welds readily with the consumables used for 355 MPa hull steel, provided the plate is dry and the joint preparation is correct. Preheat is normally not required for thin plate at ambient temperature, but it becomes necessary for thicker sections, for high restraint joints and in low ambient temperatures. Welding procedure qualification should follow the class society requirements, and welders need approval for the positions used in the yard.
Because the grade depends on toughness as well as strength, heat input during welding has to be controlled. Excessive heat input can soften the heat affected zone; too little can leave hard, brittle areas. Production welding should follow a qualified procedure rather than trial and error on the block.
Inspection and Documentation
Each plate is identified by heat number, and the mill certificate records chemistry, tensile properties, yield strength, elongation and impact energy at the specified test temperature. For classed work the society certificate is issued against that heat, and the surveyor may witness tests or review the mill's records depending on the rules and the mill's approval status.
Dimensional checks cover thickness, width, length, flatness and squareness, and surface inspection looks for laminations, seams and rolled-in scale. Ultrasonic testing, where specified, is carried out to the agreed acceptance level and reported separately. We supply the full document set with the shipment: mill certificate to EN 10204 3.1, class certificate where applicable, and third-party inspection reports from SGS, BV or Intertek if the buyer's contract requires them.
Handling and Storage
Plate is heavy and thin plate is easily bent, so lifting should use plates clamps or slings with spreader beams rather than a single hook. Stack plates on timber bearers with spacers kept in line vertically, and avoid stacking thin plate under heavy sections. Edge protection prevents damage to the plate edge, which is where weld preparation starts.
Hull steel is usually supplied with a shop primer on request. The primer protects the surface during storage and handling and must be compatible with the yard's welding and coating systems. If the plate will be stored outdoors for a long period, keep it clear of standing water and check the primer for breakdown before fabrication starts.
Packing, Shipping and Call-Off Delivery
Plates are strapped into bundles with timber dunnage, marked with heat number, size and project reference, and loaded so that the weight is distributed across the container or vessel floor. Heavy plate ships break bulk or in flat racks; thinner plate can travel in containers when the size allows. Each bundle carries a packing list that matches the certificates.
Shipyards work to a build schedule, so deliveries are often called off against a block sequence rather than shipped in one lot. We can hold stock and release plate in stages, keeping heat number traceability intact across the deliveries. Tell us the build sequence and the storage available at the yard, and the shipping plan can be matched to it rather than to the mill's rolling programme.






