304 or 316L: When the Extra 20% Is Necessary

Nov 12, 2026

Leave a message

Lissandra
Lissandra
Export sales at Kennen Steel International. Works with overseas buyers on steel plate, coil and pipe sourcing from vetted Chinese mills.

304 stainless steel sheet 2B finish

Stainless buyers ask this constantly, and the honest answer is that most 304 jobs stay 304. 316L earns its price only when chlorides are present. Paying for 316L "to be safe" on a dry indoor application is money spent on nothing; using 304 near seawater is a warranty claim waiting to happen.

The real difference

Both are austenitic, both are non-magnetic in the annealed condition, both weld easily. 316L adds 2–3% molybdenum, which is what improves resistance to chlorides and to pitting. 316L also has a lower carbon limit (0.03% max), which reduces sensitisation at weld seams - but 304L does the same thing more cheaply if molybdenum is not needed.

The number that matters is PREN (Pitting Resistance Equivalent Number), roughly Cr + 3.3 Mo + 16 N:

Grade Typical PREN Chloride tolerance
304 / 304L 18–19 Indoor, fresh water, mild food contact
316 / 316L 24–26 Coastal atmosphere, de-icing salts, chemical process, marine splash zone (light)
2205 duplex 34–36 Severe chloride, high strength demand

Roughly: below about 200 ppm chloride, 304 is fine. Above that, or in a wet and crevice-prone geometry, move to 316L. Seawater immersion is beyond both - that is duplex or super duplex territory.

Where 304 fails in practice

  • Near the coast but indoors. Salt mist travels. A 304 handrail 500 m from the sea will show pitting within a couple of years.
  • Food processing with brine or cleaning with hypochlorite. 304 passivates poorly in chloride-rich cleaning cycles.
  • Crevices and stagnant water. Pitting starts under gaskets, in overlaps, and at weld spatter.
  • Winter road salt exposure. Vehicle frames and municipal equipment in cold climates.

Where 316L is wasted money

  • Dry indoor architectural work
  • Fresh water piping at ambient temperature
  • General structural brackets with no chloride exposure
  • Anywhere 304L would do and the buyer is only upgrading because it sounds safer

What to check on the certificate

Chemical composition per heat, and specifically the molybdenum content and the carbon. "316L" without Mo reported is not proof. Also check the nickel content: 316L is typically 10–14% Ni, and mills under cost pressure sometimes run at the low end, which shows up in formability.

Watch for mixed material in one delivery. 304 and 316L look identical, and once the mill test certificate is separated from the bundle there is no way to tell them apart by eye. Physical segregation with colour-coded end caps and heat numbers on every bundle is the only reliable control.

How we supply stainless

  • 304 and 316L sheet and plate, 2B, No.4 and BA finishes, 0.3–20 mm
  • 304L / 316L to EN 10088-2 or ASTM A240, with the certificate showing full chemistry including Mo and N
  • Stainless pipe and tube, seamless and welded, in 304/304L and 316/316L
  • Physical segregation by heat with colour-coded marking, so mixed bundles cannot leave our yard
  • Cutting, edge rounding and protective film on request

If you want certainty on grade, we can arrange PMI (positive material identification) testing before shipment. It costs little and settles the argument permanently.

Related products: 304 stainless steel sheet, 316L stainless steel sheet 2B/No.4, Stainless steel pipe

Frequently asked questions

When is 316L actually necessary?

When chlorides are present: coastal air, de-icing salt, brine, chemical process, or chloride-rich cleaning cycles.

Is 304L as good as 316L?

It has the same low-carbon welding benefit but much lower chloride resistance. PREN for 304 is around 18 to 19, against 24 to 26 for 316L.

How do I confirm 316L on delivery?

Check molybdenum on the mill certificate, or run a PMI test. The two grades look identical and cannot be separated by eye.