Product Overview
A steel pipe pile is a large-diameter welded tube driven or drilled into the ground to carry structural load - jetty and quay walls, bridge piers, jacket foundations, cofferdams and heavy building foundations. ASTM A252 is the specification written specifically for this duty: it grades the pipe by yield strength (Gr.1, Gr.2, Gr.3) rather than by a fluid-service designation, because the pipe is a structural element, not a pressure line.
What matters in service is wall thickness uniformity, roundness, straightness and the weld. A pile is driven with impact energy measured in tonnes; an out-of-round pipe binds in the guide frame, a crooked one drifts off line, and a weld with incomplete fusion fails at the toe. None of these show up in a mill certificate alone, which is why dimensional and weld inspection before shipment is the real quality gate.
We supply A252 Gr.2 and Gr.3 pipe piles in SSAW (spiral submerged arc) and LSAW (longitudinal) construction, 12 to 60 inch OD, 6 to 25 mm wall, square cut or bevelled for splicing, with coating and anode provisions available.
Key Advantages
- Structural grading. A252 Gr.2 / Gr.3 gives a defined yield for pile design, unlike a line pipe grade used as a substitute.
- SSAW or LSAW as the job requires. Spiral for larger diameters and long runs; longitudinal for heavier walls and higher restraint.
- Dimensional control. Roundness, straightness and wall thickness checked because they decide whether the pile drives true.
- Weld quality documented. Seam and helical welds with UT or radiographic records on request.
- Ready for the site. Bevelled ends for splicing, mill scale removed where coating is specified, lifting points marked.
Technical Specifications
| Parameter | Gr.2 | Gr.3 |
|---|---|---|
| Standard | ASTM A252 | ASTM A252 |
| Yield strength | 35,000 psi min | 45,000 psi min |
| Tensile strength | 60,000 psi min | 66,000 psi min |
| Outside diameter | 12–60 in | 12–60 in |
| Wall thickness | 6–25 mm | 6–25 mm |
| Manufacture | SSAW / LSAW | SSAW / LSAW |
| Length | 12 m / 24 m | 12 m / 24 m |
| Ends | Square cut / bevelled | Square cut / bevelled |
| Coating | Bare / epoxy / 3LPE | Bare / epoxy / 3LPE |
Step-by-Step Manufacturing Process
- Plate or coil input. Material rolled to the required grade, with chemistry and mechanicals verified per heat.
- Forming. Spiral or longitudinal forming to the ordered diameter and wall.
- Welding. Submerged arc welding inside and outside; weld parameters recorded per pipe.
- Sizing and straightening. Diameter and roundness set, pipe straightened.
- End preparation. Square cut or bevelled; ends checked for squareness against the axis.
- Hydrostatic or NDT. Hydro test or UT/RT of the seam as specified, then dimensional and visual inspection.
Quality Assurance & Certificates
- EN 10204 3.1 certificate per heat with chemistry, yield and tensile
- Dimensional report: OD, wall thickness at four points, ovality, length, straightness
- Weld inspection records - UT, radiographic or hydrostatic, as ordered
- Coating thickness and adhesion report when coated
- Third-party inspection (SGS, BV, TUV) arranged on request, which most marine projects require
Core Applications
- Jetty and quay walls - the largest use of large-diameter pipe piles
- Bridge piers and abutments in river and estuary crossings
- Jacket and monopile foundations for offshore and near-shore structures
- Cofferdams and retaining structures for marine construction
- Heavy industrial foundations where driven piles replace mass concrete
FAQ
Gr.2 or Gr.3?
By design yield. Gr.3 is used where the pile carries heavier axial load or bending; if the geotechnical report specifies a grade, that governs. Do not substitute a line pipe grade for a structural pile without the engineer's approval.
Can the piles be spliced on site?
Yes - bevelled ends are supplied for field welding, with the bevel angle and root face matched to your welding procedure.
How are 24 m piles shipped?
Breakbulk or on deck, nested and lashed. 12 m lengths can travel in open-top containers where the diameter allows.



Frequently asked questions
Which standard and sizes does Steel Pipe Pile come in?
Standard: ASTM A252; Yield strength: 35,000 psi min; Tensile strength: 60,000 psi min.
What applications is Steel Pipe Pile specified for?
Jetty and quay walls - the largest use of large-diameter pipe piles; Bridge piers and abutments in river and estuary crossings; Jacket and monopile foundations for offshore and near-shore structures.
Which certificates come with Steel Pipe Pile?
EN 10204 3.1 certificate per heat with chemistry, yield and tensile; Dimensional report: OD, wall thickness at four points, ovality, length, straightness.


