Steel Rail (QU70 / QU80 / 43 Kg/m)

Steel Rail (QU70 / QU80 / 43 Kg/m)

Heavy-section rail for mine haulage, plant track and crane runways
Send Inquiry
Chat Now
Description
Technical Parameters

Product Overview

Steel rail is a hot-rolled profile with a wide, flat base, a narrow web and a crowned head, rolled in one piece so the head can carry wheel load while the base spreads it over the sleepers. The profiles used outside mainline railways - QU70, QU80 and the older 43 kg/m section - are the standard choice for mine haulage, plant and workshop track, transfer cars and light crane runways.

What separates rail from ordinary sections is metallurgy and straightness. Rail steel is a high-carbon, high-manganese grade (U71Mn, 900A or equivalent) rolled to a controlled hardness so the head resists shelling and wear under repeated wheel passes. A rail that is soft wears into a groove; one that is too hard and brittle spalls at the head edge. Both show up within the first year of service.

We supply QU70, QU80 and 43 kg/m rail to GB 2585 and AREMA profiles, in U71Mn or 900A, cut to 12.5 m or 25 m, with plain, drilled or fish-plated ends, and with mill certificates per heat.

Key Advantages

  • Correct profile, not a substitute. QU and kg/m sections have defined head width, web thickness and base width; matching the drawing matters because rail clips, fishplates and turnout components are profile-specific.
  • Wear-resistant head. U71Mn / 900A chemistry with controlled hardness gives predictable head wear in haulage and transfer duty.
  • Straightness and camber control. Rails are roller-straightened and checked for vertical and lateral deviation, which is what keeps a haulage track from developing a corkscrew.
  • Ends prepared to order. Plain, drilled to the fishplate pattern, or cut to the exact length for a fixed installation.
  • Full traceability. Heat number, chemistry, mechanical properties and profile dimensions on the mill certificate.

Technical Specifications

Parameter43 kg/mQU70QU80
StandardGB 2585 / AREMAGB 2585 / YB 354GB 2585 / YB 354
Nominal weight43.6 kg/m52.8 kg/m63.7 kg/m
Head width70 mm70 mm80 mm
Base width114 mm120 mm130 mm
Height140 mm120 mm130 mm
Web thickness14.5 mm18 mm26 mm
Length12.5 / 25 m12.5 m12.5 m
Steel gradeU71Mn / 900AU71MnU71Mn
EndsPlain / drilledPlain / drilledPlain / drilled

Step-by-Step Manufacturing Process

  1. Steelmaking. High-carbon, high-manganese heat with controlled sulphur and phosphorus, which govern brittleness at the head.
  2. Continuous casting. Bloom cast and conditioned, so inclusions that would become head defects are removed before rolling.
  3. Hot rolling. Rolled in a rail train with shaped passes that form head, web and base in one piece.
  4. Straightening. Roller straightening followed by measurement of vertical and lateral deviation.
  5. End preparation. Saw cut to length, then drilled to the fishplate pattern where required.
  6. Inspection. Profile dimensions, surface, straightness and hardness checked; heat number marked on the web.

Quality Assurance & Certificates

  • EN 10204 3.1 mill certificate per heat: chemistry, tensile strength, elongation and hardness
  • Profile dimension report against the ordered standard
  • Straightness report, vertical and lateral
  • Surface inspection for head and web defects, with photographs of any repaired area
  • Third-party inspection available on request

Core Applications

  • Mine haulage track - the main use of QU70 and QU80 in coal and metal mines
  • Plant and workshop track - transfer cars, kiln and furnace lines
  • Light crane runways where a QU profile is specified instead of a crane rail
  • Temporary and permanent site railways for construction and quarrying
  • Turntables and special trackwork cut to length

FAQ

QU80 or 43 kg/m - which should I specify?

By axle load and traffic. 43 kg/m suits light locomotives and low-frequency movement; QU80 carries heavier axle loads and more passes. If the drawing says QU80, do not substitute - the clips and fishplates are matched to the profile.

Can you drill the rail ends?

Yes, to the fishplate pattern of the ordered standard, or to a drawing you supply. Plain ends are also available if you drill on site.

What length should I order?

12.5 m fits standard rail flats and 40 ft containers; 25 m needs breakbulk or a flat rack. Most plant and mine track is specified in 12.5 m for handling.

Steel Rail (QU70 / QU80 / 43 kg/m)Steel Rail (QU70 / QU80 / 43 kg/m)Steel Rail (QU70 / QU80 / 43 kg/m)Steel Rail (QU70 / QU80 / 43 kg/m)

Frequently asked questions

What are the main technical parameters of Steel Rail?

Standard: GB 2585 / AREMA; Nominal weight: 43.6 kg/m; Head width: 70 mm.

Which industries use Steel Rail?

Mine haulage track - the main use of QU70 and QU80 in coal and metal mines; Plant and workshop track - transfer cars, kiln and furnace lines; Light crane runways where a QU profile is specified instead of a crane rail.

What quality documents accompany Steel Rail?

EN 10204 3.1 mill certificate per heat: chemistry, tensile strength, elongation and hardness; Profile dimension report against the ordered standard.

Send Message